Skip to content

Jog and waveform

Read the waveform, seek and scrub the playhead, and drive the platter.

Seek, scrub, and scratch a deck from the waveform and the platter. The waveform has two displays, and both show the same track at different scales.

Display Where Shows
Overview strip Along the bottom of the deck’s track info, 36 px tall The whole track in one bar, plus its loop and cue markers
Scrolling lane The waveform pane at the top of the mixer, one lane per deck A window of the track at the current zoom (24 seconds by default) with the playhead pinned in the middle

With no tracks loaded, the waveform pane reads Load tracks to see waveforms.

Moving the playhead

Gesture Where Effect
Click or tap Overview strip Seeks to that point in the track
Drag Scrolling lane Scrubs; the view follows your finger and the audio follows the drag
  1. Click or tap the overview strip to jump. The whole track is in the bar.
  2. Or drag the scrolling lane to scrub. Watch the lane follow your finger.

Dragging the lane sends seeks while you move, throttled so a fast drag does not flood the engine. A final seek follows on release. Between gestures the playhead eases back onto the engine’s position rather than jumping. Small drift is corrected gradually; only a real jump (180 ms or more, or any pause) snaps it.

Zooming

Scroll over any scrolling lane with the mouse wheel or a two-finger trackpad scroll to zoom. Scroll up zooms in, scroll down zooms out. The playhead stays in the middle, so zooming changes how much time sits on either side of it rather than where the track is.

The zoom level is shared by every deck, so both lanes stay aligned for beat matching, and it runs from 2 seconds to 120 seconds of source time. Tempo changes widen or narrow the window on their own so the musical span stays about the same. Double-click a lane to go back to the default 24 seconds.

Zoomed-in detail is fetched on demand. The window already on screen stays until the new peaks arrive, so zooming sharpens in place instead of flashing a coarser preview.

Colours

Each band of the spectrum has a fixed colour:

Band Colour
Low #FF4830
Mid #76E458
High #48BCFF

Settings → Waveform → Display holds the two ways to draw them. Display mode:

Mode Look
RGB (default) Low, mid and high mixed into one colour per bar
Filtered Three stacked bands, low widest

The section description reads “RGB mixes low/mid/high into one color. Filtered stacks the three bands.”

Overlays

Drawn on top of the waveform, in the lane and on the overview:

  • Beat lines, with every fourth beat brighter as the bar line.
  • The active loop as a filled region, and a pending loop-in as a flagged vertical line.
  • Hot cue flags at each saved cue point.
  • Saved loop blocks, dimmer than the active loop.
  • The slip shadow playhead, when S is on and the shadow has drifted away from the audible position.

The jog

The Jog tab holds a platter with a progress ring around its rim and a marker that turns with the audio. Dragging holds the platter, so with the default top mode the deck treats it as a hand on the record.

  1. Open the Jog tab.
  2. Drag anywhere on the platter to turn it. The progress ring tracks how far into the track you are.
  3. Turn it while playing to scratch.
  4. Let go. The motor picks the platter back up with a short ramp.

How the platter responds is set under Settings → Deck → Jog wheel:

Setting Options Default
Top jog mode Vinyl (scratch), Pitch bend, Ignore Vinyl (scratch)
Outer jog mode Vinyl (scratch), Pitch bend, Ignore Pitch bend

Ignore makes that surface inert. On a paused deck a Pitch bend surface scrubs instead. There is no tempo to bend when nothing is playing, so the platter moves the playhead.

The card’s description reads “Defaults for top (touch) and outer (freewheel) platter policy.” The on-screen platter counts as the top surface, so Top jog mode is what it follows.

  • Loops: the loop regions these overlays draw.
  • Hot Cues: the cue flags.
  • Tempo and sync: what the tempo fader is doing to the waveform’s zoom.