Skip to content

Troubleshooting sound

Find why Mixar is silent, one-sided, or breaking up: check the engine, the deck, its channel, the crossfader, the master output, and the routes in order.

Sound leaves Mixar through one path: the deck, its channel strip, the crossfader, the master output, and the device that bus is routed to. Headphones take a separate tap of the same signal. A missing sound is almost always one control on that path, so check them in order and stop at the first one that fails.

Audio setup routes the buses. This page assumes the routes were already saved at least once.

Follow the path

1. Is the engine running?

The mixer runs inside the audio engine, so nothing makes sound without it. With no usable output device the engine fails with No output device available, the app shows an Audio engine failed to start notice, and it keeps running silently.

  • Plug in or enable an output device, then save Settings → Audio or relaunch. Saving restarts the engine and reloads the tracks that were on the decks.
  • While the engine is stopped, the channel knobs are dimmed, the faders are inert, and a deck cannot be loaded or unloaded.

2. Is the deck playing?

A deck holds a track when its cover shows artwork and its title replaces No track loaded. Press Play; the key reads Pause while the deck moves.

A paused deck, or a deck with no track, produces no level at all. If the deck’s meter moves but you hear nothing, the deck is fine and the problem is downstream.

3. Is the channel passing?

The channel strip runs gain trim → EQ → filter → effect → meter and cue tap → fader. The controls below can mute a channel:

  • GAIN (pre-fader trim, ±24 dB) sets the overall level, and HI, MID and LOW (each ±24 dB) cut or boost their band.
  • FLT left of centre is a low-pass and right of centre is a high-pass, so a filter parked at either end keeps only part of the track.
  • The fader fully down silences the channel. The meter still shows level at that point, because it sits before the fader.

4. Is the crossfader passing this deck?

The crossfader only scales the channels assigned to the side it is on. A deck assigned to side B is silent while the crossfader sits at A, even though its meter moves.

  • Click A or B beside the crossfader to see that side’s deck checklist, and either move the crossfader to the deck’s side or assign the deck to the live side.
  • Uncheck a deck to set it to Thru, which keeps it audible across the whole crossfader travel.

5. Is the master output up?

Click the master meter at the left of the Beat FX strip to open Levels. Its Master card holds the master output fader. With that fader down, every channel is silent no matter where its strip sits.

6. Is the route right?

In Settings → Audio → Master bus, check Device, Channel mode, and the two channel numbers. A channel pair the interface does not drive is silent even though the meters move. System default follows the operating system’s current output, so unplugging headphones can move your sound to another device.

Symptom table

Symptom Likely cause Fix
The app opens, shows an audio notice, no sound No usable output device Enable an output, then save Settings → Audio or relaunch
Deck meter moves, master is silent Channel fader down, crossfader on the other side, or master level down Check steps 3 to 5
Deck meter does not move Deck paused, no track loaded, or engine stopped Press Play, load a track, or restart the engine
Only one side is audible Channel mode set to Mono (fold L+R), or a channel pair the interface does not own Switch to Stereo pair, or fix the channel numbers
Master is fine, headphones are silent Preview bus off, no channel cued, headphone level down, or blend at the master end with Master cue off See Cueing, then check the preview bus
Clicks, crackle, or dropouts Buffer size too small for the machine or the driver Raise Buffer size in Settings → Audio → Engine
Controls feel late Buffer size too large Lower it, or turn on Low latency for that bus
Mixar will not start, or a save reports Settings saved, but not applied Refused sample rate, or a Buffer size that is not a multiple of 64 Pick Device default for the rate (or an explicit rate when the device reports none), and a multiple of 64 for the buffer

Nothing in the headphones

The headphone bus is a separate route, so it can fail on its own:

  1. Preview bus enabled: Settings → Audio → Preview bus → Enable preview bus. Without it, cueing has no output at all.
  2. A deck is cued: the headphones icon in that deck’s volume column is lit.
  3. Headphone level: the top fader of the Headphone card in Levels.
  4. Blend position: the Cue / Mst fader at the Mst end plays the master tap, and that side is silent while Master cue is off.
  5. Preview channels: the preview bus must use channels the interface actually has. The defaults assume channels 3 and 4.

The cue tap sits before the channel fader, so a cued deck is audible in the headphones with its fader fully down. If headphones work and the master does not, the problem is in steps 3 to 6 of the path, not in cueing.

Sound breaks up

Clicks, crackle, and dropouts mean the engine ran out of time, not that a control is wrong.

  1. Raise Buffer size in Settings → Audio → Engine. A larger block gives the machine more room, at the cost of a little extra delay.
  2. Turn Low latency off for the bus that breaks up. When the driver reports a buffer-size range, it asks the device for its smallest block, which leaves the least headroom.
  3. Keep the value a multiple of 64 frames. The hint under the slider states the rule: Must be a multiple of 64 frames (mixer graph chunk size).
  4. If only one device breaks up, check whether other software is holding it. Two buses on one device share a single stream.

For what the buffer actually does and what each size range buys you, see Audio setup.

Where to go next

Task Page
Route the master bus and the headphones Audio setup
Every audio control, range, and default Settings → Audio
Channel strip controls and meters Channels
Crossfader sides and the master meter Mixer
Cueing and the headphone blend Cueing