Beat FX
Route a deck through the shared Beat FX unit and set a beat-synced Echo or Reverb.
Beat FX is one effect unit shared by both decks, driven from the thin strip pinned to the bottom of the mixer screen. It works like the Beat FX section of a DDJ-400: a single effect at a time, one level knob, and an on/off key. The difference is that you choose which decks feed it from the deck header.
Before you start
The audio engine must be running. The effect select, BEAT ◀ ▶, LEVEL, BEAT FX, and each deck’s FX key are inert while it is stopped.
For echo, the beat division follows the master deck’s tempo. Press Master (the crown) on the deck that should own the tempo before you set the division.
Add an effect to a deck
- Pick Echo or Reverb in the effect select.
- For Echo, step BEAT ◀ ▶ to the division you want:
1/4for a short slap,1/2or3/4for a wider trail. The pair is not shown for Reverb. - Press FX in the header of the deck you want effecting.
- Set LEVEL to taste.
- Press BEAT FX to arm the unit.
Verify
The BEAT FX label lights while the unit is on, and the deck’s FX key lights while that deck is routed. With Echo armed, the repeats you hear sit on the beat.
The strip
| Control | What it does |
|---|---|
| Effect select | Picks the effect: Echo or Reverb |
| BEAT ◀ ▶ | Steps the echo’s beat division. Hidden for effects that have no beat time (reverb) |
| LEVEL | Wet/dry mix: how much of the effect you hear |
| BEAT FX | Arms the unit. The label lights up while it is on |
The select has no “off” entry: the unit always holds an effect, and the BEAT FX key decides whether it processes anything. A fresh session loads Echo, unarmed, at 1/2 beat with LEVEL in the middle.
Routing a deck
The unit is shared, but a deck only runs through it when you ask. Press FX in the deck header to route the deck; the key lights while that deck is routed. Press it again to send the deck back to a dry signal.
Both decks run the same effect and settings: routing is what differs. Each deck keeps its own delay or reverb state, so tails never bleed from one deck into the other.
Beat-synced echo
The echo’s delay is a beat division, not a time in milliseconds, so it always sits on the grid:
1/16 · 1/8 · 1/4 · 1/2 · 3/4 · 1/1 · 2/1
The division is measured against the master deck’s tempo, including its tempo fader, so nudging the master’s pitch bends the repeats with it. While the master deck has no analysed BPM, the unit falls back to 120 BPM.
Reverb has no beat time, so the BEAT ◀ ▶ pair disappears when you select it.
Where the effect sits
The unit is an insert on the channel, after the EQ and filter and before the channel fader:
- The channel meter and your headphones already include the effect, so you can cue a wet deck before bringing it in.
- The channel fader and the crossfader scale the effect exactly like the dry signal.
- Changing the effect, switching the unit off, or unrouting a deck clears its stored tail; the next hit starts clean.
If you hear no effect
- One deck is dry: press FX in that deck’s header. The key must be lit for the deck to run through the unit.
- Both decks are dry: press BEAT FX, light FX in each deck’s header, and raise LEVEL above zero. The select always holds an effect; BEAT FX arms the unit, and each deck’s FX key decides whether that deck feeds it.
- The repeats drift off the grid: check which deck owns the tempo, and that the master deck has an analysed BPM. Without one the unit falls back to 120 BPM.
- A tail cuts out after a change: changing the effect, switching the unit off, or unrouting a deck clears the stored tail. Hit the sound again to start clean.
For the rest of the audio path, from the engine to the output route, see Troubleshooting sound.
Not there yet
- The select lists single effects. Named presets (chains of effects, Rekordbox-style) will land in the same select.
- The engine also carries echo feedback and reverb size/damping; those knobs arrive with the preset editor.
- Effect settings and routing are session state: they reset when the engine restarts, like filter, EQ and volume.
- FX has no MIDI mapping yet; it is driven from the strip.